Harmonised or product standard

    EN 1504-9 - Products and systems for the protection and repair of concrete structures - part 9: general principles for the use of products and systems

    Testing · NAC-037-TL

    In short

    EN 1504-9 - Products and systems for the protection and repair of concrete structures - part 9: general principles for the use of products and systems. For concrete repair and protection products, Amstelfy covers general principles for the use of products and systems in its ISO/IEC 17025-accredited laboratory (NAC-037-TL). Reports and certificates are written for use in CE marking files, Declarations of Performance and third-party approvals across Europe.

    What the standard covers

    EN 1504-9 is the design and specification backbone of the series. It describes how to assess a damaged structure, decide the repair strategy and select products by principle and method. Eleven principles are defined. Principles 1 to 6 address defects in the concrete: protection against ingress, moisture control, concrete restoration, structural strengthening, physical resistance and resistance to chemicals. Principles 7 to 11 address reinforcement corrosion: preserving or restoring passivity, increasing resistivity, cathodic control, cathodic protection and control of anodic areas. Each principle lists numbered methods, for example 3.1 hand-applied mortar, 3.2 recasting with concrete and 3.3 spraying, and for each method the part names the product standard and the characteristics that must be declared for that use. It is not harmonised and carries no test of its own.

    Type testing and factory production control

    Applying the part follows its own sequence: assessment of the structure and causes of deterioration, definition of the objectives of the owner, choice of principles, then methods, then products whose declared performance under parts 2 to 7 matches the characteristics the part requires for that method. For the laboratory this translates into a test programme: once the client names the method, the relevant performance characteristics, mandatory or optional for all intended uses or for certain uses, are read from the part's tables and tested under the product standard. The scope lists EN 1504-9 together with the product parts; in practice the testing is done to the part the chosen principle and method invoke.

    What the report states

    The outcome is a documented match between the repair method and the product performance: a specification that cites principle and method, and test reports under parts 2 to 7 covering the characteristics the part lists for that method. Owners and designers use this trail to show the repair was specified in accordance with the standard.

    Where the result is required

    Repair and protection specifications for bridges, tunnels, car parks, water structures, industrial and residential buildings; tender documents that call for products by principle and method; and manufacturers' system guides that map their EN 1504-2 to 1504-7 products to the methods. It also frames the maintenance strategy chosen before EN 1504-10 governs the execution on site.

    What we assess

    • general principles for the use of products and systems

    Products covered

    • concrete repair and protection products

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    Products covered by a harmonised European standard are CE marked on the basis of a Declaration of Performance; other product standards support national approvals and third-party certification. Amstelfy provides the initial type testing / type testing and, where the standard is on its ISO/IEC 17065 scope, acts as the product certification body.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    A principle states the physical or electrochemical mechanism by which deterioration is arrested, for instance restoring passivity of the steel. A method is a practical way of achieving it, such as increasing cover with mortar or replacing contaminated concrete. One principle offers several methods, each pointing to specific product standards.

    It tells you which characteristics must be declared for the method chosen and whether they are required for all or certain intended uses. The class, such as R3 or R4 for mortars, follows from the structural assessment and the product standard. The engineer selects it; the part frames the choice.

    Replacing damaged concrete alone does not stop reinforcement corrosion if chlorides or carbonation remain around the steel. Principles 7 to 11 address the electrochemical condition of the reinforcement, by realkalisation, chloride extraction, resistivity increase, cathodic protection or coating of the steel, and are combined with restoration where needed.

    Related standards

    All Concrete, fibres, mortars & concrete repair products testing