Test method

    EN 15813 - Polymer modified bituminous thick coatings - flexibility at low temperatures

    Testing · NAC-037-TL

    In short

    EN 15813 - Polymer modified bituminous thick coatings - flexibility at low temperatures. Amstelfy's laboratory determines flexibility at low temperature of PMBC coatings according to EN 15813 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.

    What EN 15813 determines

    EN 15813 determines whether a polymer modified bituminous thick coating stays flexible when cold. A fully cured film of the coating is cooled to the test temperature given in the standard and bent around a mandrel; a coating that cracks has lost the elasticity it needs to follow small movements of a basement wall during winter construction and the first heating season. The test therefore separates coatings whose polymer modification is effective at low temperature from those that become brittle. It is a pass-or-fail observation rather than a measured value: cracks visible after bending mean failure. The property is one of the required characteristics of EN 15814, alongside crack bridging and watertightness, and is an early indicator of long-term behaviour because brittle films also perform badly in the crack-bridging test.

    Specimens, conditioning and procedure

    The coating is applied to a flexible carrier at the dry film thickness declared by the manufacturer and cured under standard conditions until fully dry, which for thick emulsion coatings takes days to weeks. Several specimens are cut from the cured film. Each is conditioned at the low test temperature for the period the standard specifies, then bent around a cylindrical mandrel of the specified diameter at the specified speed while still cold, with the coating on the outside of the bend. Immediately after bending the surface is examined for cracks. The specimen preparation, in particular the thickness and the curing time, is the main source of variation, so both are recorded in the report.

    What the report states

    The report states, for each specimen, whether cracks appeared after bending at the test temperature, together with the dry film thickness, curing period and conditioning time. The characteristic is declared in the Declaration of Performance as pass (no cracks at the specified temperature); the lowest temperature at which no cracks occurred can be added when the client wants to know the margin.

    Where the result is required

    Required under EN 15814 for every CE-marked PMBC product. Manufacturers also run it during development to compare polymer types and dosages, during factory production control to catch batches with poor emulsion stability, and after storage trials to check frost-damaged stock. It is specific to thick bitumen coatings; cold flexibility of bitumen sheets is tested by EN 1109 with a different specimen and procedure.

    What we assess

    • flexibility at low temperature

    Products covered

    • PMBC coatings

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    EN 1109 bends a factory-made bitumen sheet of defined thickness around a mandrel at stepwise decreasing temperatures and reports the lowest passing temperature. EN 15813 tests a laboratory-cured film of a trowel-applied coating at the temperature EN 15814 requires and reports pass or fail. The specimens, curing and thickness are different, so results are not comparable.

    Specimens are normally prepared in the laboratory so that thickness and curing are controlled and documented. If the client prepares films, the report must state that the specimens were supplied, and the result cannot serve as type-testing evidence without documentation of how and when they were made. For CE purposes send the liquid product.

    A thick emulsion coating loses water slowly, and residual moisture plasticises the film. A film tested before it is fully dry can pass, then crack once dried in service. The standard therefore requires the film to be fully dried before conditioning, and the report records the curing period so that results can be compared.

    Related standards

    All Waterproofing membranes, roof underlays & liquid-applied systems testing