Test method

    EN ISO 12571 - Hygrothermal performance of building materials - hygroscopic sorption properties

    Testing · NAC-037-TL

    In short

    EN ISO 12571 - Hygrothermal performance of building materials - hygroscopic sorption properties. Amstelfy's laboratory determines sorption isotherms of thermal insulation products (MW, EPS, XPS, PIR, PUR, wood fibre) and building materials according to EN ISO 12571 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.

    What EN ISO 12571 determines

    EN ISO 12571 characterises the hygroscopic behaviour of a material: how much water it holds in equilibrium with the surrounding air at a given relative humidity and constant temperature. Dried specimens are exposed to a series of increasing humidities until their mass is stable at each step, giving the adsorption curve, and then to decreasing humidities, giving the desorption curve; the two together form the sorption isotherm, and their separation is the hysteresis of the material. Two techniques are allowed: the desiccator method, in which saturated salt solutions fix the humidity in closed vessels, and the climatic chamber method, in which a controlled chamber is set to each humidity. The isotherm is the input hygrothermal simulation needs to predict moisture storage, and it defines the practical moisture content used when converting thermal conductivity between conditions.

    Specimens, conditioning and procedure

    Specimens are dried to constant mass under EN ISO 12570 at the temperature suited to the material and weighed. They are then placed in desiccators over saturated salt solutions chosen to give a set of humidities spread over the hygroscopic range, or in a climatic chamber stepped through the same humidities, at a constant temperature, normally 23 °C. At each step the specimens are weighed at intervals until the mass change between successive weighings falls below the equilibrium criterion, and the humidity is then raised to the next level. After the highest level the sequence is reversed for desorption. Clients choose adsorption only or the full cycle, the number of humidity levels and the temperature; hygroscopic products need longer at each step than closed-cell foams.

    What the report states

    For each humidity level the report gives the equilibrium moisture content by mass and, where the density is known, by volume, for adsorption and for desorption, tabulated and plotted as the sorption isotherm with the hysteresis visible. Typical derived quantities are the moisture content at 23 °C and 80 % relative humidity, used as the reference state in EN ISO 10456, and the input curve for simulation software.

    Where the result is required

    Sorption isotherms are required for hygrothermal simulation under EN 15026, for moisture conversion coefficients under EN ISO 10456, for material data sets behind EPDs and building physics declarations, and for assessing hygroscopic insulation such as wood fibre, cellulose, hemp and cork, as well as plasters, mortars and wood-based panels. Mineral wool and polystyrene show very low sorption and are usually tested only to document that fact.

    What we assess

    • sorption isotherms

    Products covered

    • thermal insulation products (MW, EPS, XPS, PIR, PUR, wood fibre)
    • building materials

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    The sequence is governed by the material, not the clock: each humidity step continues until the mass is stable, and a dense hygroscopic product may need weeks per step, while foams equilibrate quickly. A full adsorption and desorption cycle at five levels is therefore a long test, which is why clients often request adsorption only for a first data set.

    Both are permitted and give comparable isotherms. The desiccator method uses saturated salt solutions and suits small specimens and many parallel materials; the chamber method handles larger specimens and humidities not available from salts. The choice depends on specimen size and the humidity levels wanted, and the report names the method and the salts or set points used.

    Water that has condensed in narrow pores and in the ink-bottle shaped voids of the material is released at a lower humidity than it entered, so a drying material retains more moisture at a given humidity than a wetting one. This hysteresis is a real material property and matters for drying-out simulations, which is why the standard measures both branches.

    Related standards

    All Thermal insulation products & hygrothermal test methods testing