Test method

    EN 1849-1 - Flexible sheets for waterproofing - thickness and mass per unit area - bitumen sheets

    Testing · NAC-037-TL

    In short

    EN 1849-1 - Flexible sheets for waterproofing - thickness and mass per unit area - bitumen sheets. Amstelfy's laboratory determines thickness and mass per unit area of bitumen sheets according to EN 1849-1 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.

    What EN 1849-1 determines

    EN 1849-1 determines the thickness and the mass per unit area of bitumen waterproofing sheets, the two quantities by which a bitumen sheet is identified and by which factory production control checks that the right amount of compound has been applied to the carrier. Thickness is measured with a dial gauge whose foot presses on the sheet under a defined load. Mass per unit area is found by weighing a piece of known area. Which of the two the product standard asks the manufacturer to declare depends on the surfacing: a sheet with a smooth or fine-sanded surface declares thickness, while a sheet with coarse mineral granules declares mass per unit area, because granules make the thickness reading meaningless. Both appear in the declaration with the tolerances the product standard permits.

    Specimens, conditioning and procedure

    Specimens are cut across the full width of the sheet at the positions the standard specifies, with release films removed, and conditioned at the standard temperature. For thickness, the gauge with the specified foot diameter and contact pressure is applied at a number of points distributed over the width, and the readings are recorded; on sheets with coarse surfacing the measurement is made only where the standard allows or omitted. For mass per unit area, a specimen of accurately measured area is weighed on a balance of adequate resolution and the mass is divided by the area. Mean values and the spread across the width are calculated and compared with the declared nominal values.

    What the report states

    The report states the thickness in mm as mean and individual values across the width, or notes that it is not determined for a granule-surfaced sheet, and the mass per unit area in kg/m² as the mean of the specimens, together with the nominal values and tolerances declared by the manufacturer and a statement of conformity. These values also identify the sheet in all other test reports of the programme.

    Where the result is required

    Required by EN 13707, EN 13969, EN 13970, EN 14695 and EN 13859-1 as declared characteristics and as the identification of every bitumen sheet tested; also the routine factory production control measurement on the coating line, since mass per unit area reveals the compound application and thickness the uniformity across the web. Roofing specifications set minimum thicknesses for torch-on sheets so that enough compound is available for the lap bond. Plastic and rubber sheets are measured by EN 1849-2.

    What we assess

    • thickness and mass per unit area

    Products covered

    • bitumen sheets

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    The granules on a slate-surfaced sheet stand proud of the bitumen by a variable amount, so a gauge foot resting on them reads the granule height rather than the sheet. Product standards therefore have such sheets declare mass per unit area, which captures the amount of material, and reserve the thickness declaration for sheets with a smooth, sanded or film-finished surface.

    A defined contact pressure through a foot of defined diameter, fixed in the standard so that a bitumen compound, which yields under a sharp point, is not indented and so that different laboratories read the same value. The report states that the measurement follows the standard; the exact foot and load are part of the method and are not varied.

    Thickness and mass per unit area identify the sheet and are quoted in every other test report so that results can be tied to a specific product and production run. Factory production control compares them with the type-tested values at each production check, and a drift in mass per unit area is the usual first sign of a change on the coating line.

    Related standards

    All Waterproofing membranes, roof underlays & liquid-applied systems testing