Harmonised or product standard
EN 13253 - Geotextiles - erosion control works
In short
EN 13253 - Geotextiles - erosion control works. For geotextiles / geosynthetic barriers, Amstelfy covers certification of conformity (AVCP) and acts as ISO/IEC 17065-accredited product certification body (NAC-026-PPS) for this standard. Reports and certificates are written for use in CE marking files, Declarations of Performance and third-party approvals across Europe.
What the standard covers
EN 13253 is the harmonised product standard for geotextiles used in erosion control works: filters under rock armour, riprap and concrete block revetments on coasts, rivers and canals, and bank and slope protection against waves and currents. The characteristics declared for the filtration, separation and, where declared, reinforcement functions are the index properties of the EN 13249 series, with the emphasis set by the environment: characteristic opening size and water permeability to retain the bank soil under reversing flow, tensile strength, static puncture and dynamic perforation to survive armour stone placed from above, and durability including weathering, because revetment filters are often exposed through the voids of the armour. Abrasion damage and seam strength apply in specific conditions of use. A Declaration of Performance under AVCP system 2+ follows type testing and certified factory production control.
Type testing and factory production control
The type-testing programme follows the function table of the standard: tensile strength and elongation to EN ISO 10319 in both directions, static puncture to EN ISO 12236, dynamic perforation to EN ISO 13433, characteristic opening size to EN ISO 12956, water permeability to EN ISO 11058 and weathering to EN 12224, with the polymer-specific screening tests for the 25-year durability statement. Where the manufacturer declares resistance to abrasion for revetments with moving stones, the sliding-block abrasion test cited by the standard is added, and seam strength to EN ISO 10321 is tested when panels are sewn for placement under water. Factory production control follows the frequencies in the standard's annex; certification adds audit sampling.
What the report states
The manufacturer receives reports stating each characteristic with mean and tolerance, retained strengths for the durability tests in percent and, where tested, the abrasion loss and seam efficiency, plus an FPC assessment. These feed the Declaration of Performance and the CE label with the function pictograms. Under a voluntary certification scheme the declared values are confirmed on independently sampled product and the certificate is maintained by surveillance.
Where the result is required
EN 13253 is required for CE marking of geotextiles supplied for coastal defences, breakwater and dyke revetments, river and canal bank protection, scour aprons and bridge pier protection, and for filter layers under gabions and concrete block mats. Designers select products using the declared opening size and permeability against the bank soil and the declared mechanical values against the armour grading and placement method. Products that remain exposed, such as some erosion control mats, need durability evidence beyond the standard statement.
What we assess
- certification of conformity (AVCP)
Products covered
- geotextiles / geosynthetic barriers
Accreditation status
| Activity | Standard | Accreditation | Validity | On scope |
|---|---|---|---|---|
| Testing | ISO/IEC 17025:2017 | NAC-037-TL | valid until 2 December 2028 | No |
| Product certification | ISO/IEC 17065:2012 | NAC-026-PPS | valid until 31 January 2030 | Yes |
| Validation & verification | ISO/IEC 17029:2019 | NAC-006-VV | valid until 31 January 2030 | No |
Route to market
Products covered by a harmonised European standard are CE marked on the basis of a Declaration of Performance; other product standards support national approvals and third-party certification. Amstelfy provides the initial type testing / type testing and, where the standard is on its ISO/IEC 17065 scope, acts as the product certification body.
How it works
1
Send the standard number, product description and intended use
2
We confirm the applicable test series, sample quantities and timeline
3
Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)
4
You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.
Frequently asked questions
Related standards
- EN ISO 9862 - Geosynthetics - sampling and preparation of test specimens
- EN ISO 9863-1 - Geosynthetics - thickness at specified pressures - single layers
- EN ISO 9864 - Geosynthetics - mass per unit area of geotextiles and geotextile-related products
- EN ISO 10318 - Geosynthetics - terms and definitions
- EN ISO 10319 - Geosynthetics - wide-width tensile test
- EN ISO 10321 - Geosynthetics - tensile test for joints/seams by wide-width strip method
- EN ISO 11058 - Geotextiles - water permeability characteristics normal to the plane, without load
- EN ISO 12236 - Geosynthetics - static puncture test (CBR test)