Test method

    EN ISO 10321 - Geosynthetics - tensile test for joints/seams by wide-width strip method

    Testing · NAC-037-TL

    In short

    EN ISO 10321 - Geosynthetics - tensile test for joints/seams by wide-width strip method. Amstelfy's laboratory determines seam/joint tensile strength of geotextiles, geogrids and geocomposites according to EN ISO 10321 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.

    What EN ISO 10321 determines

    EN ISO 10321 applies the wide-width tensile method to a specimen that contains a seam or joint across its middle, so that the connection rather than the parent material is loaded. It covers sewn seams in geotextiles, thermally or adhesively bonded joints and mechanical connections in geogrids such as bodkin joints, provided a 200 mm wide specimen can be gripped. The quantity determined is the maximum force per unit width that the joint transfers before it fails, and the ratio of that force to the strength of the unjoined material from EN ISO 10319 gives the seam efficiency in percent. The failure mode is recorded as well, because a seam that fails by thread rupture, by fabric tearing next to the stitch line or by slippage of the stitched layers points to different corrective actions.

    Specimens, conditioning and procedure

    Specimens are prepared so that the seam lies centrally between the clamps and perpendicular to the direction of loading, with the same 200 mm width and the gauge length defined in the standard; the seam type, thread, stitch density and overlap, or the welding parameters, are recorded. The number of specimens follows the parent-material test, and parent specimens from the same material are tested to EN ISO 10319 in the same programme. Clamping, extension rate and strain measurement follow EN ISO 10319. The force is recorded to failure and the mode of failure is identified: seam thread, fabric adjacent to the seam, pull-out or slippage. Factory seams and site seams made with the client's equipment can both be tested.

    What the report states

    The report gives the seam tensile strength in kN/m for each specimen with mean and coefficient of variation, the corresponding parent-material strength, and the seam efficiency as a percentage. Failure modes are listed per specimen. The manufacturer declares seam strength where the product standard requires it for the intended use, and installers use the efficiency to decide whether sewn seams or overlaps are acceptable for a design.

    Where the result is required

    The product standards EN 13249 to EN 13257 and EN 13265 list tensile strength of seams and joints as a characteristic relevant where seams are used in the application, for example in reinforcement layers, in coastal and bank revetments under EN 13253 and in large lined reservoirs under EN 13254. It is also used to qualify prefabricated sewn panels, factory-welded geogrid joints and site sewing procedures for geotextile tubes and containers.

    What we assess

    • seam/joint tensile strength

    Products covered

    • geotextiles
    • geogrids
    • geocomposites

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    Sewn seams transfer only a fraction of the parent strength, often between about half and three quarters, because the needle perforations and the thread limit the force path. Thermally bonded joints in some wovens can approach the parent strength. The test shows where a specific seam design lies, which is why it is specified per seam type.

    The load is applied perpendicular to the seam line, because that is how a seam is stressed in service when two panels are pulled apart. The parent-material reference test is run in the same fabric direction as the strips crossing the seam, so that the efficiency compares like with like.

    Yes, provided the connection can be built into a 200 mm wide specimen and held in the clamps; bodkin joints and welded or sewn overlap connections are tested this way. The number of ribs crossing the joint is recorded, and the force is converted to kN/m with the rib pitch as in EN ISO 10319.

    Related standards

    All Geotextiles & geosynthetics testing