Test method
EN ISO 6892-1 – Metal tensile test
Metallic materials - tensile testing at room temperature
In short
EN ISO 6892-1 - Metallic materials - tensile testing at room temperature. Amstelfy's laboratory determines yield and tensile strength, elongation, reduction of area of steel rods, bars, plates, wire according to EN ISO 6892-1 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.
What EN ISO 6892-1 determines
EN ISO 6892-1 is the reference tensile test for metals at room temperature. A specimen of known cross-section is strained to fracture at a controlled rate while force and extension are recorded, and the standard defines how to derive the upper and lower yield strength, the proof strength at 0.2 % non-proportional extension where no yield plateau exists, the tensile strength, the percentage elongation after fracture on a proportional or fixed gauge length, the total extension at maximum force and the reduction of area. Two control methods are allowed: method A controls strain rate, which removes the influence of machine stiffness on strain-rate-sensitive steels, and method B controls stress rate in the elastic range. The result characterises the delivered material against its product standard and feeds anchor, fastener and reinforcement assessments.
Specimens, conditioning and procedure
Specimens are either full-section pieces of wire, bar or small profiles, or machined round or flat specimens taken from plate, forgings or thick bars as the product standard requires. The original cross-section is measured and the gauge length marked; the proportional gauge length relates to the cross-section so that elongation values of different sizes are comparable. The test is run in a machine of the required force class with an extensometer of the required class for yield and proof strength; the strain or stress rates of the chosen method are maintained through the yield region and may be increased afterwards. After fracture the broken halves are fitted together to measure the final gauge length and the minimum cross-section.
What the report states
The report states, per specimen, ReH and ReL or Rp0.2 in MPa, Rm in MPa, A in % with the gauge length used, Agt and Z where required, the ratio Rm/Re where a product standard asks for it, the control method and rates, specimen geometry and fracture location, with the force-extension curve. Results are compared with the specified minimum values of the material grade when the client names it.
Where the result is required
Steel tensile properties are needed for the steel parts of anchors assessed under EADs 330232, 330499 and 330008, for anchor channels and cast-in parts, for threaded rods and wire in scaffold and lifting products, for reinforcing steel and prestressing components, and for the steel plates and nosings of expansion joints and bearings. Verifying the mill certificate on the actual batch is the first step in most fastener programmes; the method is also used for failure analysis and incoming inspection by manufacturers.
What we assess
- yield and tensile strength, elongation, reduction of area
Products covered
- steel rods, bars, plates, wire
Accreditation status
| Activity | Standard | Accreditation | Validity | On scope |
|---|---|---|---|---|
| Testing | ISO/IEC 17025:2017 | NAC-037-TL | valid until 2 December 2028 | Yes |
| Product certification | ISO/IEC 17065:2012 | NAC-026-PPS | valid until 31 January 2030 | No |
| Validation & verification | ISO/IEC 17029:2019 | NAC-006-VV | valid until 31 January 2030 | No |
Route to market
This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.
How it works
1
Send the standard number, product description and intended use
2
We confirm the applicable test series, sample quantities and timeline
3
Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)
4
You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.
Frequently asked questions
Related standards
- EN ISO 527-4 - Plastics - tensile properties - isotropic and orthotropic fibre-reinforced composites
- EN ISO 14125 - Fibre-reinforced plastic composites - flexural properties
- EN ISO 527-1 - Plastics - tensile properties - general principles
- EN ISO 527-3 - Plastics - tensile properties - films and sheets
- EN ISO 527 - Plastics - determination of tensile properties
- EN ISO 604 - Plastics - compressive properties
- EN ISO 178 - Plastics - flexural properties
- EN ISO 62 - Plastics - water absorption