Test method

    EN 13719 - Geosynthetics - long term protection efficiency of geotextiles in contact with geosynthetic barriers

    Testing · NAC-037-TL

    In short

    EN 13719 - Geosynthetics - long term protection efficiency of geotextiles in contact with geosynthetic barriers. Amstelfy's laboratory determines protection efficiency of geotextiles, geogrids and geocomposites according to EN 13719 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.

    What EN 13719 determines

    EN 13719 assesses whether a protection geotextile prevents a geosynthetic barrier, usually a geomembrane in a landfill, reservoir or dam, from being deformed and locally strained by the aggregate placed on it. A layered assembly is built in a rigid cylinder: a soft metal plate that acts as a deformation indicator, the barrier, the protection geotextile under test and the drainage aggregate, with a loading plate above. A sustained vertical pressure representing the overburden is applied for the long duration prescribed in the standard, after which the indentations in the indicator plate are surveyed and converted into local strain. It is a performance test: aggregate, pressure and temperature represent the project or a reference condition, and the result expresses how much point loading reaches the membrane. Strain limits are set by the specifier or national guidance, not by the method.

    Specimens, conditioning and procedure

    The client provides the protection geotextile and, for a project-specific test, the aggregate and geomembrane to be used; otherwise reference materials are used. The assembly is built in the test cylinder in the order base, indicator plate, barrier, geotextile, aggregate and load plate, with the aggregate placed to a controlled density. The agreed vertical pressure is applied through a loading frame and held constant at the test temperature for the full duration, which runs to days rather than hours. After unloading the indicator plate is removed and the depth and shape of every indentation are measured; from these the local elongation of the plate, and hence of the barrier, is calculated. The geotextile and the barrier are inspected and photographed.

    What the report states

    The report gives the maximum local strain in the indicator plate in percent, the number, depth and spacing of indentations, the applied pressure, temperature and duration, the aggregate description and the condition of the geotextile and barrier after the test. Where the client has named a limit, the report states whether the measured strain lies below it. Manufacturers use it to declare protection efficiency under the relevant product standard, designers to select the geotextile mass for a given cover material.

    Where the result is required

    Protection efficiency to EN 13719 is the characteristic for the protection function in the geotextile standards that cover lined structures: EN 13254 for reservoirs and dams, EN 13255 for canals, EN 13256 for tunnels, EN 13257 for solid waste and EN 13265 for liquid waste containment. Landfill regulators in several European countries require it for the geotextile between the drainage gravel and the base liner, and it is used for cushion layers under armour stone in reservoirs and for the protection of tunnel waterproofing sheets.

    What we assess

    • protection efficiency

    Products covered

    • geotextiles
    • geogrids
    • geocomposites

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    No. CBR is a short-term index on the geotextile alone. EN 13719 loads the complete system of aggregate, geotextile and barrier for a long period and measures the strain transmitted to the barrier, which depends on stone shape, pressure, temperature and creep of the geotextile. Two products with equal CBR force can protect a membrane very differently.

    For a project-specific result, the actual drainage aggregate and the pressure from the final overburden, often increased by a factor for long-term effects set by the regulator. For a product declaration a reference aggregate and reference pressures are used so that geotextiles can be compared. The laboratory needs the choice before the assembly is built.

    The method does not set one. National landfill guidance commonly limits the long-term local strain in HDPE geomembranes to a fraction of one percent to avoid stress cracking, and reservoir designers may accept other values. The report gives the measured strain so that it can be checked against whichever criterion the project applies.

    Related standards

    All Geotextiles & geosynthetics testing