Harmonised or product standard

    EN 1341 - Slabs of natural stone for external paving

    Certification · NAC-026-PPS

    In short

    EN 1341 - Slabs of natural stone for external paving. For natural stone products, Amstelfy covers certification of conformity (AVCP) and acts as ISO/IEC 17065-accredited product certification body (NAC-026-PPS) for this standard. Reports and certificates are written for use in CE marking files, Declarations of Performance and third-party approvals across Europe.

    What the standard covers

    EN 1341 is the harmonised product standard for natural stone slabs used as external paving: units wider than 150 mm and, in general, more than twice as wide as they are thick, laid on bedding in pedestrian and trafficked areas. Setts are covered by EN 1342 and kerbs by EN 1343. The declared characteristics are dimensions with tolerance classes, flexural strength from which the breaking load of a slab format is derived, slip resistance of the surface finish, abrasion resistance for trafficked surfaces, freeze-thaw resistance, water absorption, surface finish and the petrographic denomination. Reaction to fire is class A1 without testing. Conformity is shown by type testing, factory production control and a Declaration of Performance under the AVCP system given in Annex ZA. The required breaking load comes from the paving design, not from the standard.

    Type testing and factory production control

    Type testing samples slabs per stone type and finish. Flexural strength is determined to EN 12372 on specimens cut from the slabs, with the statistical treatment in the standard giving the declared value; freeze-thaw resistance to EN 12371 is reported as the flexural strength after cycling; water absorption to EN 13755; slip resistance to EN 14231 on the as-supplied finish, subject to the standard's provision for coarse textured finishes; abrasion resistance to EN 14157, with the wide wheel method as reference; dimensions and flatness to EN 13373; and petrography to EN 12407. Factory production control covers block selection, sawing and finishing, dimensional checks and periodic repeat of the type tests. Certification audits the FPC and samples slabs for verification.

    What the report states

    The report states the flexural strength in MPa with the lower expected value and the breaking load derived for the declared slab thickness and format in kN, the flexural strength after freeze-thaw cycling with the percentage loss, water absorption in percent, the unpolished slip resistance value, abrasion as groove width or volume loss, and the dimensional tolerance class achieved. The manufacturer declares these in the Declaration of Performance and on delivery documents for each slab format.

    Where the result is required

    EN 1341 is required for CE marking of natural stone paving slabs supplied in the EU and EEA for squares, pedestrian streets, footways, terraces, pool surrounds and lightly trafficked areas, and it is referenced by public procurement and by paving design guides that convert the declared flexural strength into a bedding and thickness design. Granite, basalt, porphyry, sandstone, limestone and quartzite slabs from European and imported sources are declared to it. Setts and kerbs from the same quarry are declared under EN 1342 and EN 1343.

    What we assess

    • certification of conformity (AVCP)

    Products covered

    • natural stone products

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028No
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030Yes
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    Products covered by a harmonised European standard are CE marked on the basis of a Declaration of Performance; other product standards support national approvals and third-party certification. Amstelfy provides the initial type testing / type testing and, where the standard is on its ISO/IEC 17065 scope, acts as the product certification body.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    It is on the ISO/IEC 17065 certification scope NAC-026-PPS; the related test methods are on the ISO/IEC 17025 testing scope.

    EN 12372 gives the flexural strength of the stone on small specimens; the standard's statistical method turns the results into a lower expected value, and the breaking load for a slab is calculated from that strength and the slab's width and thickness. Designers compare it with the load class required for the traffic on the paved area.

    For fine finishes such as sawn, honed or polished surfaces, which are tested with the pendulum to EN 14231 in the as-supplied state. Coarse textured finishes such as flamed, bush-hammered or riven surfaces are covered by the standard's provision that they need no testing, provided the finish is declared and maintained in production.

    All three cover natural stone for external paving from the same stone types. EN 1341 is for slabs, units with a width over 150 mm and generally more than twice the thickness; EN 1342 is for setts, small cubic or rectangular units; EN 1343 is for kerbs. The characteristics overlap, but test specimens, tolerances and the strength declaration differ.

    Related standards

    All Natural stone & masonry ancillary components testing