Harmonised or product standard

    EN 131-6 - Ladders - part 6: telescopic ladders

    Testing · NAC-037-TLCertification · NAC-026-PPS

    In short

    EN 131-6 - Ladders - part 6: telescopic ladders. For portable ladders, Amstelfy covers strength, deflection, torsion and durability tests in its ISO/IEC 17025-accredited laboratory (NAC-037-TL) and acts as ISO/IEC 17065-accredited product certification body (NAC-026-PPS) for this standard. Reports and certificates are written for use in CE marking files, Declarations of Performance and third-party approvals across Europe.

    What the standard covers

    EN 131-6 covers leaning and standing telescopic ladders, defined as ladders with three or more rung sections whose stiles slide inside one another, and hinge-joint telescopic ladders with lockable hinge positions. The hazards specific to the type are uncontrolled collapse and trapped fingers, so the part requires a locking mechanism on each stile of every extended section, a visible indication that each lock is engaged, equal rung spacing in the extended state and squeezing protection, either a distance device that keeps the user's fingers clear of the closing rungs or a braking function that slows the collapse. Sections must not separate without tools and screws must be secured against loosening. For strength, deflection, torsion and durability the part applies the EN 131-2 tests with its own preconditioning and additional cycling of the locks, and the general dimensions follow EN 131-1.

    Type testing and factory production control

    Testing starts with preconditioning by dropping the retracted ladder onto a concrete floor, repeated after rotating it, to represent rough handling before the locks are tested. Locking and indicator function is checked on every section. The ladder is then subjected to stile strength and bending, lateral deflection, rung loading, torsion and base slip tests in the extended position at the set-up angle specified, and to durability cycling of extension, locking and retraction followed by repeat strength tests. Squeezing protection is verified by measuring the distance device or timing the controlled collapse. Pull-out of feet and end caps and the security of section separation are also tested. Professional or non-professional loads and cycles follow EN 131-2.

    What the report states

    The report records the condition of each lock and indicator after preconditioning and cycling, the strength and deflection results against the limits for the tested length, the squeezing protection measurements and the outcome of the slip and pull-out tests. The ladder is classed professional or non-professional and the marking, including instructions on checking the locks before each use, is verified under EN 131-3.

    Where the result is required

    Telescopic ladders are sold in large volumes online and through retail, and they have been subject to repeated market surveillance campaigns and recalls for lock failures and finger injuries. Importers and brand owners use EN 131-6 testing to qualify suppliers and to respond to authority requests, retailers require it before listing, and professional users ask for the professional class. Manufacturers re-test when the lock pin, spring or stile extrusion changes.

    What we assess

    • strength, deflection, torsion and durability tests

    Products covered

    • portable ladders

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030Yes
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    Products covered by a harmonised European standard are CE marked on the basis of a Declaration of Performance; other product standards support national approvals and third-party certification. Amstelfy provides the initial type testing / type testing and, where the standard is on its ISO/IEC 17065 scope, acts as the product certification body.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL and on the ISO/IEC 17065 certification scope NAC-026-PPS.

    Telescopic ladders are carried and set down roughly, and their locks and indicators are sensitive to impact damage. The preconditioning drop, repeated after turning the ladder, represents that handling so that the locking and strength tests are made on a ladder in a realistic condition rather than on a factory-fresh specimen.

    Either a distance device that keeps the user's hands at least 80 mm from the closing rungs, or a braking function that slows the retraction so that a section collapses over about 1.5 seconds per 300 mm. The feature is measured or timed in the test, and the instructions must explain how to retract the ladder safely.

    No. Ladders with extension elements, such as push-up or rope-operated extending ladders, are excluded from Part 6 and tested under EN 131-2. Part 6 applies to ladders whose stiles telescope rung by rung, including models with hinges that are also subject to the EN 131-4 hinge requirements.

    Related standards

    All Scaffolding, temporary works equipment & ladders testing