Harmonised or product standard

    EN 1065 - Adjustable telescopic steel props - product specifications, design and assessment by calculation and tests

    Testing · NAC-037-TLCertification · NAC-026-PPS

    In short

    EN 1065 - Adjustable telescopic steel props - product specifications, design and assessment by calculation and tests. For telescopic steel props, Amstelfy covers characteristic load capacity by testing in its ISO/IEC 17025-accredited laboratory (NAC-037-TL) and acts as ISO/IEC 17065-accredited product certification body (NAC-026-PPS) for this standard. Reports and certificates are written for use in CE marking files, Declarations of Performance and third-party approvals across Europe.

    What the standard covers

    EN 1065 is the product standard for adjustable telescopic steel props used in falsework and formwork support. It defines five classes, A to E, each with a characteristic nominal strength that for classes A, B and C falls with increasing extension length and for classes D and E is a constant value over the whole extension range. The designation combines the class letter with the maximum extension length, for example D55 for a class D prop extending to 5.50 m. The standard fixes minimum wall thicknesses, overlap between inner and outer tube, end-plate details, the pin and collar adjustment device and corrosion protection, and then requires the strength to be demonstrated either by calculation with prescribed imperfections and load eccentricity or by tests, or by a combination of the two.

    Type testing and factory production control

    Props are tested as complete units in a compression rig that reproduces the end conditions, load eccentricity and inclination specified in the standard, so that the test captures the real imperfection sensitivity of a slender two-tube member. Tests are made at the minimum and maximum extension and at intermediate lengths, with the pin set in the adjustment holes as in use, and loaded to failure while axial load and lateral deflection are recorded. Material coupons from the tubes are tested for yield strength so that results can be corrected to nominal values. Additional checks cover the pin and collar under load, end-plate strength and the function of the anti-slip device. Evaluation follows the statistical approach of EN 12811-3.

    What the report states

    The report states, for each extension tested, the ultimate load of every specimen and the derived characteristic resistance in kN, compared with the class requirement at that length. A curve of characteristic capacity against extension defines the class and maximum length that can be marked on the prop. Dimensional and material results are listed against the requirements of the standard, and the certificate records the designation.

    Where the result is required

    Formwork contractors select props by class and extension from the EN 1065 designation when supporting slab formwork, beams and back-propping, and falsework designers to EN 12812 take the characteristic capacity from it. Hire companies specify certified props to control mixed fleets. Manufacturers and importers of props use the test programme for initial type verification, for production control of tube supply and for re-qualification after a change in pin, collar or end-plate design.

    What we assess

    • characteristic load capacity by testing

    Products covered

    • telescopic steel props

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030Yes
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    Products covered by a harmonised European standard are CE marked on the basis of a Declaration of Performance; other product standards support national approvals and third-party certification. Amstelfy provides the initial type testing / type testing and, where the standard is on its ISO/IEC 17065 scope, acts as the product certification body.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL and on the ISO/IEC 17065 certification scope NAC-026-PPS.

    Classes A, B and C have a characteristic strength that decreases as the prop is extended, so the capacity must be read for the actual length in use. Classes D and E provide a constant characteristic strength at every extension, which simplifies site use but requires heavier tubes and is typically chosen for heavy slab and beam support.

    The standard requires the strength to be shown across the whole range, so tests are made at the fully retracted and fully extended lengths and at intermediate positions, because the governing failure can switch between the inner tube, the outer tube and the overlap region. The number of positions and specimens is agreed in the test plan.

    Partly. The standard allows assessment by calculation using the imperfections and eccentricity it prescribes, but the pin, collar and end-plate behaviour and the real interaction of the tubes are normally confirmed by tests. Most manufacturers combine a calculation for the capacity curve with tests at selected extensions.

    Related standards

    All Scaffolding, temporary works equipment & ladders testing