Harmonised or product standard

    EN 1263-1 - Temporary works equipment - safety nets - safety requirements, test methods

    Testing · NAC-037-TLCertification · NAC-026-PPS

    In short

    EN 1263-1 - Temporary works equipment - safety nets - safety requirements, test methods. For safety nets, Amstelfy covers energy absorption (drop test), mesh strength and ageing in its ISO/IEC 17025-accredited laboratory (NAC-037-TL) and acts as ISO/IEC 17065-accredited product certification body (NAC-026-PPS) for this standard. Reports and certificates are written for use in CE marking files, Declarations of Performance and third-party approvals across Europe.

    What the standard covers

    EN 1263-1 specifies safety nets of polypropylene or polyamide used to catch persons falling during construction and assembly work. Nets are classified by energy absorption capacity, class A requiring 2.3 kJ and class B 4.4 kJ, and by maximum mesh size, 60 mm for type 1 and 100 mm for type 2, giving classes A1, A2, B1 and B2. Four systems are defined by their support: S nets with a border rope, T nets on horizontal brackets, U nets on a vertical supporting framework and V nets on gallows-type supports. The standard sets requirements for mesh ropes, border, tie and coupling ropes and joints, and requires the as-new energy absorption to include a safety factor and an ageing factor for the loss of strength over at least a year of service. Installation is covered separately in EN 1263-2.

    Type testing and factory production control

    Specimens are complete nets with the test meshes attached, plus separate mesh samples and rope lengths. After conditioning in the climate specified, mesh samples are loaded to failure to establish the energy absorbed at break, both new and after artificial ageing by exposure to light, from which the ageing factor is derived. Border, tie and coupling ropes are tensile tested for breaking force, including at joints. The dynamic test drops a spherical test mass into the installed net system and checks that the net retains the mass, that deflection stays within the limit for the system type and that no mesh or edge rope breaks. Each net also carries test meshes that the user removes annually for retesting.

    What the report states

    The report states the energy absorption of the mesh in kJ new and aged, the resulting ageing factor, rope breaking forces in kN against the minimum values, and the outcome of the dynamic test with the measured deflection. The net is assigned its class and system type, which, together with the manufacturing date and the test mesh identification, appear on the label required by the standard.

    Where the result is required

    Safety nets to EN 1263-1 are used under roof work, steel erection, bridge decks and in multi-storey construction wherever collective fall protection is preferred to harnesses, and national regulations in most European countries require nets to carry the class marking. Contractors and hire companies also rely on the annual test mesh procedure to decide whether a net stays in service. Manufacturers use the tests for type approval and for production control of each netting batch.

    What we assess

    • energy absorption (drop test)
    • mesh strength
    • ageing

    Products covered

    • safety nets

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030Yes
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    Products covered by a harmonised European standard are CE marked on the basis of a Declaration of Performance; other product standards support national approvals and third-party certification. Amstelfy provides the initial type testing / type testing and, where the standard is on its ISO/IEC 17065 scope, acts as the product certification body.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL and on the ISO/IEC 17065 certification scope NAC-026-PPS.

    Test meshes are spare meshes made from the same netting and attached to the net at manufacture. Because polymer netting loses strength with light exposure, the user detaches a test mesh after each year of service and sends it for an energy absorption test. The result shows whether the net still meets the class requirement.

    Class A nets must absorb at least 2.3 kJ in the mesh test and class B at least 4.4 kJ. Class B is required where the possible fall height or the net span is larger. Mesh size, 60 mm or 100 mm, is chosen independently, so a B1 net combines the higher energy class with the smaller mesh.

    A complete net of the system type with its border rope and test meshes, additional lengths of mesh rope, border, tie and coupling rope for tensile tests, and the manufacturing documents stating fibre type, rope constructions and knot or joining method. For T, U and V systems the bracket or frame design drawings are needed to arrange the dynamic test.

    Related standards

    All Scaffolding, temporary works equipment & ladders testing