Harmonised or product standard

    EN 131-1 - Ladders - part 1: terms, types, functional sizes

    Testing · NAC-037-TL

    In short

    EN 131-1 - Ladders - part 1: terms, types, functional sizes. For portable ladders, Amstelfy covers classification, marking and requirements in its ISO/IEC 17025-accredited laboratory (NAC-037-TL). Reports and certificates are written for use in CE marking files, Declarations of Performance and third-party approvals across Europe.

    What the standard covers

    EN 131-1 is the foundation of the portable ladder series. It defines the terms used in all other parts, lists the ladder types, including leaning, standing, extending, combination, hinge-joint, telescopic and platform ladders, and fixes their functional sizes: rung and step spacing, minimum inside widths, the length of stiles above the top step, the inclination of standing ladders and the overlap of extending sections. The 2015 revision, amended in 2019, introduced the requirement that leaning ladders longer than 3 m, including combination ladders used in the leaning mode, have a widened base, normally a stabiliser bar whose length depends on ladder length. The part contains no tests of its own; it provides the dimensional and configuration requirements that the test parts verify, and the designation system used in marking.

    Type testing and factory production control

    In laboratory work EN 131-1 is applied as the dimensional and configuration check at the start of every ladder programme. The ladder type is identified and its designation confirmed. Rung spacing and its uniformity, inside width between stiles, top-rung clearance, stile extension, the set-up angle of standing ladders, overlap of extending sections and the base width with any stabiliser are measured with calibrated rules, gauges and inclinometers in the position of use. Hinges, locks and stays are checked for the configurations the type allows. Any deviation is reported before strength, torsion or durability testing to EN 131-2, EN 131-4, EN 131-6 or EN 131-7 begins, because those tests assume a ladder that already meets the functional sizes.

    What the report states

    The report lists each measured dimension against the functional size required for the ladder type, states the designation and classification confirmed, and records whether the widened base is present and correctly sized for ladders over 3 m. The dimensional record becomes part of the type-test file for the ladder and is cited in later test reports and certificates.

    Where the result is required

    All ladder manufacturers and importers selling in Europe reference EN 131-1 for type designation and dimensions, and market surveillance authorities use it when checking products at retail. It is the entry point for conformity evidence on ladders, which are consumer and work equipment rather than construction products. Retailers' specifications, tender documents for professional ladders and rental fleets quote the EN 131-1 type and length alongside the EN 131-2 class.

    What we assess

    • classification, marking and requirements

    Products covered

    • portable ladders

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    Products covered by a harmonised European standard are CE marked on the basis of a Declaration of Performance; other product standards support national approvals and third-party certification. Amstelfy provides the initial type testing / type testing and, where the standard is on its ISO/IEC 17065 scope, acts as the product certification body.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    The 2015 revision responded to accident data showing that sideways tipping is a main cause of falls from leaning ladders. A widened base increases the resistance to overturning, and the required width grows with ladder length. Extension and combination ladders that can be used leaning are included, and a removable upper section must also comply.

    It defines functional sizes and types rather than an overall limit, but the dimensional rules and the widened base requirement become more demanding with length, and the test parts specify loads and deflection limits that grow with length. Very long ladders are therefore constrained by the test requirements rather than by a stated maximum.

    EN 131-1 provides the terms and functional sizes for all types, including hinge-joint ladders. The strength and durability tests come from EN 131-2, and the hinge-specific requirements from EN 131-4. A multi-purpose ladder is checked in every configuration it can be set up in, which is why the type identification under Part 1 comes first.

    Related standards

    All Scaffolding, temporary works equipment & ladders testing