Test method

    ISO 48-4 - Rubber, vulcanized or thermoplastic - indentation hardness by durometer (Shore)

    Testing · NAC-037-TL

    In short

    ISO 48-4 - Rubber, vulcanized or thermoplastic - indentation hardness by durometer (Shore). Amstelfy's laboratory determines Shore hardness of rubber compounds, elastomeric bearings and seals and waterstops according to ISO 48-4 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.

    What ISO 48-4 determines

    ISO 48-4 specifies the measurement of indentation hardness of rubber with a durometer, the instrument formerly covered by ISO 7619-1. A spring-loaded indentor protrudes from the flat foot of the instrument; when the foot is pressed onto the rubber the indentor is pushed back by an amount that depends on the balance between spring force and the resistance of the material, and the scale reads from 0 at full protrusion to 100 at full retraction. Type A uses a truncated cone and a weaker spring for soft to medium rubbers; type D uses a sharper cone with a rounded tip and a stiffer spring for hard rubbers and ebonite-like materials. The standard also covers types AO and AM for very soft and for thin materials.

    Specimens, conditioning and procedure

    Test pieces need a flat surface and sufficient thickness for the type, with the option of plying thinner layers of the same material when the standard allows. The durometer is mounted on a stand that applies the foot at a controlled rate and with the specified mass, which removes the operator influence of hand-held readings. After conditioning, the foot is brought into full contact and the reading is taken after the dwell time given in the standard, which is a few seconds for vulcanised rubber and longer for thermoplastic rubber. Readings are taken at several positions away from the edges and the median is formed.

    What the report states

    The report gives the hardness as a number followed by the durometer type, for example Shore A or Shore D, together with the dwell time, number of readings, test piece thickness and any plying. Values are the median of the set. For aged, immersed or low-temperature-exposed material the change in Shore units from the initial median is stated, which is the form used by EN 681-1 and by waterstop and profile specifications.

    Where the result is required

    Shore A is the hardness quoted on nearly every rubber compound data sheet and on waterstops, sealing profiles, gaskets, expansion joint seals and rubber sheeting; Shore D covers hard rubbers and some thermoplastic elastomer parts. The test is a standard item in factory production control, in incoming inspection of elastomer components, and in ETA and certification programmes where hardness identifies the compound and tracks its change after ISO 188 heat ageing or ISO 1817 immersion.

    What we assess

    • Shore hardness

    Products covered

    • rubber compounds
    • elastomeric bearings and seals
    • waterstops

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    Shore A is intended for soft to medium-hard rubber. When readings approach the top of the A scale the method loses resolution and the standard recommends switching to type D, which has a sharper indentor and a stronger spring. Conversely, very low A readings point to the AO scale. The report always names the type used.

    ISO 48-4 requires the durometer to be applied by a stand at a defined rate with a defined mass and the reading to be taken after a fixed dwell. Hand-held readings vary with pressing force, speed and timing and tend to read higher because they are taken immediately. Both may be useful in production, but only the stand measurement is reported to the standard.

    Yes, provided the total thickness under the foot meets the minimum for the type, which can be achieved by plying several layers of the same material as the standard allows. Very thin products are better measured with the type AM durometer or the IRHD micro test under ISO 48-2, and the report states which route was taken.

    Related standards

    All Rubber, elastomers, sealants & adhesives testing