Test method

    ISO 815 - Rubber, vulcanized or thermoplastic - compression set

    Testing · NAC-037-TL

    In short

    ISO 815 - Rubber, vulcanized or thermoplastic - compression set. Amstelfy's laboratory determines compression set of rubber compounds, elastomeric bearings and seals and waterstops according to ISO 815 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.

    What ISO 815 determines

    ISO 815 measures the ability of a rubber to recover its thickness after being held under a constant compressive strain. Cylindrical test pieces are compressed by 25 per cent between parallel plates with spacers, kept at the chosen temperature for the chosen time, released, allowed to recover at standard temperature and re-measured. Compression set is the part of the imposed deformation that is not recovered, expressed as a percentage. Part 1 covers ambient and elevated temperatures, where the set reflects cross-link rearrangement, further curing and oxidative ageing; Part 2 covers low temperatures, where crystallisation and glass transition dominate. The property is central to sealing products, because a seal that takes a set loses contact pressure against the mating surface.

    Specimens, conditioning and procedure

    Two test piece sizes are defined: type A, 29 mm diameter and 12.5 mm thick, and type B, 13 mm diameter and 6.3 mm thick; they are moulded or, where the product allows, cut and built up from the product. Thickness is measured, the pieces are placed between the plates of a compression device, and spacers set the 25 per cent strain. The loaded device is held in an oven, or in a low-temperature chamber for Part 2, for the agreed time and temperature from the preferred series in ISO 23529. After release the test pieces recover for 30 minutes at standard temperature on a wooden surface and the final thickness is measured.

    What the report states

    Compression set is reported in per cent for each test piece and as the median of the set, with the test piece type, temperature, duration, whether lubricant was used and the recovery conditions. A low value indicates good recovery. Product standards set maximum values; EN 681-1, for example, limits compression set of pipe seals at the temperatures and times it defines, and the report states the result against such a limit when the client names it.

    Where the result is required

    Compression set is a requirement in standards for elastomeric pipe and tunnel seals (EN 681-1), elastomeric bearings (EN 1337-3), window and curtain-wall gaskets, waterstops and bridge expansion joint seals, and in many OEM specifications for gaskets and O-rings. It is also used in development to compare cure systems and polymer types, and in factory production control as a sensitive indicator of under-cure.

    What we assess

    • compression set

    Products covered

    • rubber compounds
    • elastomeric bearings and seals
    • waterstops

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    The product standard or the client's specification normally fixes them; typical combinations are 24 hours at 70 °C for general-purpose elastomers and 72 hours at the service temperature for seals. Where nothing is specified the laboratory proposes conditions from the preferred series in the standard and states them in the report, because results at different conditions are not comparable.

    Only where test pieces of the standard shape can be cut or built up from the product with the required thickness; ISO 815 allows pieces assembled from layers for this purpose. For products too thin or too irregular, moulded test pieces from the same compound are used and the report states the origin of the pieces.

    Part 1 covers ambient and elevated temperatures, where the set measures permanent changes from further cross-linking and ageing. Part 2 covers low temperatures, where the apparent set comes from stiffening and crystallisation that recover slowly as the material warms, so recovery is measured at the test temperature and at intervals. Seals for cold climates often need both.

    Related standards

    All Rubber, elastomers, sealants & adhesives testing