Harmonised or product standard

    EN 10083-1 - Steels for quenching and tempering - general technical delivery conditions

    Testing · NAC-037-TL

    In short

    EN 10083-1 - Steels for quenching and tempering - general technical delivery conditions. For QT steels, Amstelfy covers mechanical properties in its ISO/IEC 17025-accredited laboratory (NAC-037-TL). Reports and certificates are written for use in CE marking files, Declarations of Performance and third-party approvals across Europe.

    What the standard covers

    EN 10083-1 gives the general technical delivery conditions for steels intended for quenching and tempering, with the grade-specific compositions and properties in Part 2 for non-alloy steels such as C45E and in Part 3 for alloy steels such as 42CrMo4. Part 1 defines the heat treatment conditions in which the steel may be supplied, from untreated or normalised through soft annealed to quenched and tempered, the designation of these conditions, the concept of the ruling section to which the mechanical properties apply, purchaser options such as hardenability bands, and the inspection and testing to be carried out: cast and product analysis, tensile test, impact test, hardness and hardenability, surface quality and inspection documents. For a testing laboratory it is the reference for verifying that the steel of a safety component is the grade and condition the manufacturer declares.

    Type testing and factory production control

    Material verification starts from the manufacturer's inspection certificate, which names the grade, heat and delivery condition. Test pieces are taken from the component or from a representative bar at the location and orientation that the ruling section rules prescribe, so that the result reflects the properties the standard guarantees for that thickness. The tensile test to EN ISO 6892-1 gives yield strength, tensile strength, elongation and reduction of area; Charpy V-notch impact tests are made at the specified temperature where the grade or option requires them; hardness is measured on the surface and, where relevant, as a traverse through the section. Chemical analysis confirms the grade. Hardenability is checked by the end-quench test only when ordered as an option.

    What the report states

    The report lists the measured yield and tensile strength in N/mm², elongation and reduction of area in per cent, impact energy in joules and hardness, each against the range for the grade, ruling section and delivery condition stated, with the chemical analysis compared to the composition limits. The conclusion states whether the material is consistent with the declared grade and condition, which the manufacturer files with the component's type documentation.

    Where the result is required

    Quenched and tempered steels are specified for shackle bodies and pins to EN 13889, for scaffold coupler bolts and forgings, for anchor rods and threaded components, for prop and jack parts and for lifting hooks and links. Material verification to EN 10083 is part of initial type testing and of surveillance under product certification, and it is the first step in most failure investigations. Steel producers and forges use it as their delivery specification.

    What we assess

    • mechanical properties

    Products covered

    • QT steels

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    Products covered by a harmonised European standard are CE marked on the basis of a Declaration of Performance; other product standards support national approvals and third-party certification. Amstelfy provides the initial type testing / type testing and, where the standard is on its ISO/IEC 17065 scope, acts as the product certification body.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    The ruling section is the thickness or diameter at which the heat treatment determines the properties guaranteed by the standard. Because quenching hardens a thick section less completely than a thin one, the same grade has lower guaranteed strength for larger ruling sections, and test pieces must be taken from a position that represents it.

    The certificate documents what the steelmaker tested on the cast and delivery condition. It does not prove that the heat treatment of the finished forging achieved the intended properties, so product standards for shackles and couplers normally require tests on the component itself or on heat-treated representative pieces as well.

    Tensile properties and hardness in the expected range for the grade and ruling section, together with impact energy where specified, indicate that the part was quenched and tempered rather than normalised or left untreated. A hardness traverse through the section and, if needed, microstructure examination settle doubtful cases.

    Related standards

    All Steel wire, wire ropes & lifting accessories testing