Test method

    EN 12004-2 - Adhesives for ceramic tiles - test methods

    Testing · NAC-037-TL

    In short

    EN 12004-2 - Adhesives for ceramic tiles - test methods. Amstelfy's laboratory determines adhesion, open time, slip, deformation of adhesives, tile adhesives and tapes according to EN 12004-2 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.

    What EN 12004-2 determines

    EN 12004-2 collects the test methods for adhesives for ceramic tiles that were previously spread across separate standards, including EN 1348 tensile adhesion, EN 1346 open time, EN 1308 slip, EN 12002 transverse deformation, EN 1324 and EN 12003 shear adhesion for dispersion and reaction resin adhesives, and EN 1323 for the concrete slab. Each method isolates one aspect of how an adhesive behaves on site: adhesion strength after curing and exposure, how long the combed bed remains able to wet a tile, how far a tile slides on a vertical wall before the adhesive stiffens, how much the cured bed can bend before cracking, and how well the adhesive wets the tile back. The results are evaluated against the requirements of EN 12004-1 to assign the type and the optional characteristics F, T, E, S1 and S2.

    Specimens, conditioning and procedure

    Cementitious adhesives are combed onto standard concrete slabs and tested for tensile adhesion with reference tiles after the four conditioning regimes; open time is determined by placing tiles at extended intervals after combing and measuring the adhesion that remains; slip is measured as the downward movement of a loaded tile on a vertical slab; transverse deformation is measured on a cured strip of adhesive loaded centrally in bending until failure; early tensile adhesion is used for fast-setting claims. Dispersion and reaction resin adhesives are tested in shear between tiles, after standard curing and after heat, water or thermal shock as the type requires. Wetting capability is assessed visually on the tile back after a set open time.

    What the report states

    Reports state tensile or shear adhesion strength in N/mm² per conditioning regime with the failure pattern, open time as the adhesion remaining after the interval tested, slip in mm, transverse deformation in mm and wetting as a percentage of the tile back covered. Values are presented against the thresholds of EN 12004-1: 0.5 and 1.0 N/mm² for C1 and C2, slip of 0.5 mm or less for T, 2.5 mm or 5 mm deformation for S1 and S2.

    Where the result is required

    The methods provide the type-testing and factory production control evidence for cementitious, dispersion and reaction resin tile adhesives declared under EN 12004-1, including the optional F, T, E, S1 and S2 designations, and for audit testing in certification schemes. Manufacturers of adhesives for large-format porcelain, natural stone, swimming pools and underfloor heating use the deformation and open time methods to substantiate data sheet claims and installation guidance.

    What we assess

    • adhesion, open time, slip, deformation

    Products covered

    • adhesives
    • tile adhesives
    • tapes

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    A cementitious adhesive with that designation needs tensile adhesion after all four conditioning regimes at 1.0 N/mm² or more for C2, slip of 0.5 mm or less for T, extended open time with adhesion of at least 0.5 N/mm² after 30 minutes for E, and transverse deformation of at least 2.5 mm and below 5 mm for S1. Reaction to fire and dangerous substances complete the declaration.

    A strip of cured adhesive of defined dimensions is supported at both ends and loaded at mid-span until it cracks; the deflection at failure is the transverse deformation. It indicates how well the adhesive accommodates movement between a tile and a substrate that shrinks, deflects or is heated, which is why S1 and S2 adhesives are specified for large tiles, underfloor heating and timber-based substrates.

    Dispersion (D) and reaction resin (R) adhesives are tested in shear: two tiles bonded with a defined adhesive layer are pushed apart parallel to the bond. D adhesives are tested after standard curing, heat ageing, water immersion and at elevated temperature; R adhesives after standard curing, water immersion and thermal shock. Cementitious (C) adhesives use the tensile pull-off on concrete slabs.

    Related standards

    All Rubber, elastomers, sealants & adhesives testing