Test method

    EN ISO 8510-1 - Adhesives - peel test for flexible-bonded-to-rigid assemblies - 90 degree peel

    Testing · NAC-037-TL

    In short

    EN ISO 8510-1 - Adhesives - peel test for flexible-bonded-to-rigid assemblies - 90 degree peel. Amstelfy's laboratory determines 90 degree peel strength of adhesives, tile adhesives and tapes according to EN ISO 8510-1 under its ISO/IEC 17025 accreditation (NAC-037-TL). The method is typically part of initial type testing, ETA test programmes or factory production control verification; results are reported in English for manufacturers across Europe.

    What EN ISO 8510-1 determines

    EN ISO 8510-1 measures the peel resistance of an adhesive bond between a flexible adherend, such as a film, foil, fabric or thin sheet, and a rigid adherend when the flexible member is pulled away at 90 degrees to the rigid surface. The peel front is a line, so the force needed to advance it per unit width reflects the energy absorbed by the adhesive, the interface and the bending of the flexible member. At 90 degrees the flexible adherend bends through a right angle only, so its stiffness contributes less to the result than in the 180 degree arrangement, and the angle must be held constant by the apparatus as separation proceeds. The method applies to tapes, laminating adhesives, membranes bonded to boards and metals, and coatings on flexible backings.

    Specimens, conditioning and procedure

    Specimens consist of a strip of the flexible adherend bonded to a rigid plate over a defined length, with a free end left for gripping; bonding follows the adhesive manufacturer's instructions for application, pressure and cure, and the specimens are conditioned before testing. The rigid adherend is fixed to a carriage that moves horizontally as the crosshead rises, so that the free end of the flexible adherend is always perpendicular to the plate at the peel front. The crosshead moves at the constant rate specified, and the force is recorded against displacement over the full bonded length. The start and finish of the trace are discarded and the mean peel force is evaluated for each specimen.

    What the report states

    The report gives the peel resistance of each specimen as the mean force over the evaluated length per unit width, in N/mm or N per 25 mm, the set mean, the peel rate, the adherends, the bond line and cure conditions, and the type of failure observed along the peel path, whether adhesive, cohesive, delamination of the flexible adherend or substrate failure. Minimum and maximum force are given when the trace shows stick-slip.

    Where the result is required

    The 90 degree peel is used for self-adhesive membranes and tapes bonded to boards and metals, for laminating adhesives in panel production, for coatings and films on rigid substrates, and in product assessment work where a bonded flexible layer must stay attached under service conditions, including after ageing or immersion. It is the European route to peel data where a specification calls for EN ISO 8510 and the 90 degree arrangement, and complements ASTM D903 or D3330 data for US submissions.

    What we assess

    • 90 degree peel strength

    Products covered

    • adhesives
    • tile adhesives
    • tapes

    Accreditation status

    ActivityStandardAccreditationValidityOn scope
    TestingISO/IEC 17025:2017NAC-037-TLvalid until 2 December 2028Yes
    Product certificationISO/IEC 17065:2012NAC-026-PPSvalid until 31 January 2030No
    Validation & verificationISO/IEC 17029:2019NAC-006-VVvalid until 31 January 2030No

    Route to market

    This test method is used inside initial type testing, ETA assessment programmes and factory production control verification. Amstelfy reports it as an accredited test under NAC-037-TL, either stand-alone or as part of a complete test programme.

    How it works

    1. 1

      Send the standard number, product description and intended use

    2. 2

      We confirm the applicable test series, sample quantities and timeline

    3. 3

      Samples are delivered to Veilmeesterweg 20, 1187 ZW Amstelveen (Mon-Fri 09:00-17:00)

    4. 4

      You receive the report in English, written for the TAB, Notified Body, evaluation service or programme operator.

    Frequently asked questions

    Yes - it is listed on the ISO/IEC 17025 testing scope NAC-037-TL.

    The 90 degree arrangement is preferred when the flexible adherend is relatively stiff, for example a coated fabric, a metal foil laminate or a thick membrane, because bending it back through 180 degrees would add stiffness effects to the force. It is also chosen when the application loads the bond at a right angle, such as a membrane lifted from a board.

    A tensile testing machine with a force transducer in the appropriate range and a fixture that translates the rigid adherend as the flexible one is pulled, so that the angle at the peel front stays at 90 degrees. Without such a carriage the angle drifts during the test and the force reading changes with it, which is why hand-held or fixed-plate set-ups are not acceptable.

    The standard sets a specimen width and a minimum bonded length so that a steady peel can be evaluated after discarding the start and finish; the free end must be long enough to reach the grip. Clients bonding their own specimens receive a drawing with the dimensions, and several strips per condition are needed so that the mean is meaningful.

    Related standards

    All Rubber, elastomers, sealants & adhesives testing